|
ИСТИНА |
Войти в систему Регистрация |
ИСТИНА ИНХС РАН |
||
The CMS Magnetic Field Map (II): The CMS Magnetic Field Measuring and Monitoring Systemsстатья Глава в книге
- Авторы: Klyukhin Vyacheslav, Ball Austin, Bergsma Felix, Boterenbrood Henk, Curé Benoit, Dattola Domenico, Gaddi Andrea, Gerwig Hubert, Hervé Alain, Loveless Richard, Teafoe Gary, Wenman Daniel, Zeuner Wolfram, Zimmerman Jerry
- Сборник: Current Perspective to Physical Science Research
- Том: 7
- Глава в коллективной монографии
- Год издания: 2024
- Место издания: Book Publisher International Kolkata, West Bengal, India
- Первая страница: 37
- Последняя страница: 70
- DOI: 10.9734/bpi/cppsr/v7/8666A
- Аннотация: This chapter is the second part in a series of publications on the Compact Muon Solenoid (CMS) detector magnetic field map creation. The CMS detector at the Large Hadron Collider has a heterogeneous solenoid magnet where the created magnetic flux penetrates both nonmagnetic and ferromagnetic materials of the experimental setup. The chapter describes the performance of the magnetic field measuring and monitoring systems for the CMS detector. To cross-check the magnetic flux distribution obtained with the CMS magnet model, four systems for measuring the magnetic flux density in the detector volume were used. The magnetic induction inside the 6 m diameter superconducting solenoid was measured and is currently monitored by four nuclear magnetic resonance (NMR) probes installed using special tubes at a radius of 2.9148 m outside the barrel hadron calorimeter at ±0.006 m from the coil median XY-plane. Two more NMR probes were installed at the faces of the tracking system at Z-coordinates of −2.835 and +2.831 m and a radius of 0.651 m from the solenoid axis. The field inside the superconducting solenoid was precisely measured in 2006 in a cylindrical volume of 3.448 m in diameter and 7 m in length using ten three-dimensional (3D) B-sensors based on the Hall effect (Hall probes). These B-sensors were installed on each of the two propeller arms of an automated field-mapping machine. In addition to these measurement systems, a system for monitoring the magnetic field during the CMS detector operation has been developed. Inside the solenoid in the horizontal plane, four 3D B-sensors were installed at the faces of the tracking detector at distances X = ±0.959 m and Z-coordinates of −2.899 and +2.895 m. Twelve 3D B-sensors were installed on the surfaces of the flux-return yoke nose disks. Seventy 3D B-sensors were installed in the air gaps of the CMS magnet yoke in 11 XY-planes of the azimuthal sector at 270°. A specially developed flux loop technique was used for the most complex measurements of the magnetic flux density inside the steel blocks of the CMS magnet yoke. The flux loops are installed in 22 sections of the flux-return yoke blocks in grooves of 30 mm wide and 12–13mm deep and consist of 7–10 turns of 45-wire flat ribbon cable. The areas enclosed by these coils varied from 0.3 to 1.59 m2 in the blocks of the barrel wheels and from 0.5 to 1.12 m2 in the blocks of the yoke endcap disks. Measurement of the magnetic flux density in the steel blocks of the magnet yoke using flux loops and three-dimensional B-sensors confirmed the correctness of the magnetic flux distribution modelling in the muon momenta measuring system, which provided a high muon momentum resolution and a reliable muon identification. The development of the magnetic field measurement and monitoring systems and the results of the magnetic flux density measurements across the CMS magnet are presented and discussed in this chapter.
- Добавил в систему: Клюхин Вячеслав Иванович
Прикрепленные файлы
| № | Имя | Описание | Имя файла | Размер | Добавлен |
|---|---|---|---|---|---|
| 1. | Полный текст | Chapter 3 - Publication Certificate | Publication_certificate_chapter3.jpg | 174,0 КБ | 19 февраля 2024 [klyukhin] |
| 2. | Полный текст | Глава 3 | Klyukhin_2024_BP_8666A.pdf | 1,2 МБ | 15 февраля 2024 [klyukhin] |